NestCut Back to the nesting studio

NestCut · Guide

How to Nest SVG Parts for Laser Cutting, Step by Step

Nesting means arranging cut parts on a sheet so that less material is left over. Doing it by hand works for two or three parts, but with a dozen different shapes you usually leave gaps that nobody notices until the sheet is gone. This guide walks through the whole workflow in NestCut, from preparing the file to checking the exported layout, and points out the mistakes that cost real material.

6 minute read · Last updated: 13 November 2026

What nesting software actually does

A nesting tool tries many positions and orientations for every part and keeps the arrangement that fits best. The headline number is utilization: the area of your parts divided by the area of the sheet they use. If utilization is 80 percent, 20 percent of the sheet is waste.

No tool can promise the perfect layout. Finding the best arrangement of irregular shapes is a hard problem, so results depend on the shapes, the spacing and the number of rotations you allow. The practical goal is a layout that is clearly better than what you would draw by hand, in a few minutes.

Step 1: Prepare the SVG

Most bad nesting results come from a bad file. Every part should be a closed outline, text should be converted to paths, and there should be no frame or background rectangle around the design. Our guide on preparing SVG files for nesting has the full checklist; do that first.

Step 2: Import and set quantities

Use the Import button and choose your SVG. NestCut treats every outline that is not inside another outline as a part, and every outline inside it as a hole that belongs to that part, so the hole always moves with its part. After import, the parts list shows each part with its size and a quantity box. Set the quantity for each part to the number you want to cut.

Step 3: Set the sheet

Open the settings and enter the sheet width and height, and choose whether you want to work in millimetres or inches. If a job does not fit on one sheet, increase the number of sheets; pieces that do not fit continue onto the next sheet. If your sheet has a damaged edge or a clamp zone, enter a slightly smaller sheet so nothing is placed where you cannot cut.

Step 4: Choose spacing and rotations

  • Space between parts: the gap NestCut keeps between neighbouring parts. It should be at least your cutter's kerf plus a safety margin. See our kerf guide for typical values.
  • Part rotations: how many orientations NestCut may try for each part. The default is 4 (0, 90, 180 and 270 degrees). Use 1 if the material has a grain you must respect.
  • Optimization type: Gravity packs parts upward from the bottom edge; Reverse gravity packs downward from the top edge. Try both and keep the better one.

Step 5: Run the nesting and read the result

Press Start nest. When it finishes, NestCut shows the material used, the waste, the number of pieces placed and, if there are any, the number of pieces it could not place. If some pieces are unplaced, add a sheet, lower the spacing, allow more rotations or reduce the quantities.

Step 6: Export and check before you cut

Export the layout as an SVG. The exported file is sized in millimetres to match your sheet, and each part keeps its holes. Before cutting expensive material, open the file in your laser software and check three things:

  1. The sheet size shown in your software matches the real sheet.
  2. A part you know the size of measures correctly.
  3. No two parts touch or overlap.

A quick test cut on scrap material is cheaper than a ruined sheet.

Common questions

Why are some pieces left unplaced? Usually the sheet is too small for the whole job, a single part is larger than the sheet in every orientation you allow, or the spacing is larger than it needs to be. Add a sheet, enter the real sheet size, allow more rotations, or reduce the spacing and quantities.

Can I nest different SVG files together? Yes. Import each file in turn and each file's outlines are added to the same parts list. Set the quantity for every part, then nest them all in one run so small parts can fill gaps between large ones.

How long does nesting take? It depends on the number of parts, how detailed their outlines are and how many rotations you allow. Small jobs finish quickly; large jobs with many curved parts take longer, and you can stop a run if you do not want to wait.

Keep reading

  • How to Prepare an SVG File for Nesting: A Checklist
  • What Is Kerf? How to Set Part Spacing for Laser, Plasma and CNC
  • How to Save Plywood and Acrylic: 8 Practical Nesting Tips

See all guides

Try it on your own partsNestCut nests SVG outlines in your browser. New accounts start with 0 credits, and you earn credits by watching a short rewarded ad.Open the tool
© 2026 NestCut
ExamplesGuidesAboutPrivacy PolicyTerms of UseContact